Dongfeng Kinrun VR 4×2 9 m³ Water Tank 8 m³ Wet Sweeper
Dongfeng Kinrun VR 4×2 8 m³ Wet Sweeper Truck
The Dongfeng Kinrun VR wet sweeper combines negative-pressure debris suction with high-pressure road cleaning in a dual-engine configuration. It carries a 9 m³ SUS304 stainless-steel clean water tank and an 8 m³ debris hopper, supporting road sweeping, sewage recovery, curb cleaning, dust suppression and targeted washing. The separate chassis and auxiliary engines allow the vehicle to travel and operate its cleaning equipment through independent power systems.
Dual-Engine Power Configuration
The Dongfeng DFH1180EX8 chassis uses a Cummins B6.2NS6B230 engine rated at 169 kW (230 PS), meeting the National VI emission standard. A separate Cummins QSB4.5-C170 auxiliary engine delivers 125 kW (170 PS) to operate the centrifugal fan, high-pressure cleaning pump and hydraulic equipment. Independent engine power allows the cleaning system to operate without relying on the chassis engine for its main working functions.
9 m³ Water Tank and 8 m³ Debris Hopper
The 9 m³ clean water tank is made from SUS304 stainless steel and incorporates internal anti-surge baffles and electronic water-level monitoring. The 8 m³ debris hopper uses reinforced corrugated SUS304 stainless steel and discharges through a hydraulic tipping mechanism with an angle of at least 48°. High-pressure internal cleaning nozzles help remove accumulated sediment after unloading. Low-water protection automatically shuts down the high-pressure pump when the water supply falls below the specified level.
Independent Hydraulic Sweep Brushes
Two Φ850 mm sweep brushes are mounted symmetrically on the vehicle's left and right sides, each driven by an independent hydraulic motor. Their three-speed electronic adjustment provides operating speeds of 50, 80 and 110 r/min, while independent lifting and retraction allow one-sided or full-width sweeping. Wear-resistant polypropylene and steel-wire brush filaments handle road debris, and an elastic buffer mechanism allows the brushes to retract when encountering obstacles.
Floating Suction Nozzle and High-Pressure Fan System
A central dual-inlet floating suction nozzle uses spring loading and four adjustable support rollers to follow changes in road surface height. Its Φ180 mm inlet is specified to handle particles up to 100 mm, with internal high-pressure jets helping loosen sediment for suction recovery. The XFS-8.0 centrifugal fan provides a stated airflow of 23,500 m³/h and total pressure of 3,500 Pa, driven through a synchronous belt by the auxiliary engine.
Dual Water Systems for Washing and Dust Suppression
The low-pressure water circuit uses a Hangzhou Weilong 80QZF-60/90N self-priming centrifugal pump, rated at 60 m³/h flow and 90 m head. It supplies the brush atomising nozzles, rear spray system, front flushing outlets and curb-washing equipment. A separate PINFL PF36 high-pressure plunger pump delivers 122 L/min at a rated pressure of 10 MPa, with a stated peak pressure of 16 MPa for the central flushing boom, hopper cleaning nozzles and handheld spray gun.
Cab-Based Electronic Control and Monitoring
A dedicated sanitation vehicle controller manages the operating sequences through a 7-inch CAN-bus touchscreen with physical keys. The display provides auxiliary engine speed, coolant temperature, oil pressure, water level and fault alarms. Four panoramic cameras monitor the sweep brushes, suction nozzle and rear working area, giving the operator visibility of the main cleaning mechanisms during operation.
Hydraulic and Pneumatic Operating Systems
The auxiliary engine drives a gear-type hydraulic pump supplying the brush lifting mechanisms, suction nozzle, hopper tipping cylinders and automatic hose reel. Pneumatic controls operate the auxiliary engine clutch, water circuit valves and pipeline air-purge system. A manual emergency hydraulic pump provides a backup method for mechanism retraction and hopper tipping if the auxiliary engine fails or the battery is discharged.
Road-Cleaning Performance and Operating Range
The vehicle has a stated maximum sweeping width of 3,500 mm and a theoretical sweeping capacity of up to 70,000 m²/h. Sweeping speeds are specified at 3–10 km/h, while high-speed flushing can operate at 8–15 km/h. With a full 9 m³ water tank, the stated continuous operating duration is approximately 3.5–4.5 hours under normal cleaning conditions, with a sewage recovery rate of at least 90% in washing mode. Actual performance depends on road conditions, water usage and the selected operating functions.
Sweeping System and Components
| Item | Details |
|---|---|
| Sweeping System Type | Wet sweeping and vacuum suction system; dual hydraulic brush discs + central floating suction nozzle |
| Main Brushes | - |
| Side Brushes | 2 units; independent hydraulic drive and lifting; automatic obstacle avoidance with elastic buffer retraction and automatic reset |
| Hopper / Debris Tank Capacity | 8 m³; reinforced corrugated SUS304 stainless steel construction |
| Hopper Unloading Method | Hydraulic tipping discharge; tipping angle ≥48°; high-pressure internal self-cleaning nozzles |
| Auxiliary Engine (Fan Drive) | Cummins QSB4.5-C170, 125 kW (170 PS) @ 2,200 rpm; Stage III; water-cooled diesel engine |
| Suction Fan / Blower | XFS-8.0 three-dimensional-flow centrifugal fan; airflow 23,500 m³/h; total pressure 3,500 Pa; 2,700 rpm; timing belt drive |
| Suction Nozzle | Centre-mounted dual-inlet floating suction nozzle; 2,400 mm wide; inlet Ø180 mm; maximum particle size ≤100 mm; 4 adjustable support rollers |
| Clean Water Tank Capacity | 9 m³; SUS304 stainless steel; anti-surge baffles; liquid level sensor and low-water protection |
| Water Spray System | Low-pressure Hangzhou Weilong 80QZF-60/90N self-priming centrifugal pump; 60 m³/h, 90 m head; high-pressure PINFL PF36 plunger pump; 122 L/min, 10 MPa working pressure, 16 MPa peak pressure |
| Hydraulic System | Auxiliary-engine-driven gear pump; approx. 100 L hydraulic oil capacity; solenoid directional valve bank; CAN-bus control; manual emergency hydraulic pump |
| Sweeping Width | 3,500 mm |
| Maximum Sweeping Capacity | 70,000 m²/h |
| Sweeping Operating Speed | 3–10 km/h |
| Control System | Dedicated sanitation vehicle controller; 7-inch CAN-bus touchscreen with physical keys; programmed operating sequences, fault diagnosis and four panoramic cameras |
| Lighting / Safety | Amber rotating warning beacon, rear working lamp, reverse buzzer, operating and warning indicator lights; low-water and auxiliary engine fault alarms |
Chassis Parameters
| Item | Details |
|---|---|
| Chassis Brand / Model | Dongfeng Kinrun VR DFH1180EX8 |
| Drive Configuration | 4×2 |
| Engine Model / Power | Cummins B6.2NS6B230, 169 kW (230 PS) @ 2,200 rpm |
| Emission Standard | China National VI |
| Transmission / Gears | Fast 8JS85T, 8-speed manual |
| Wheelbase | 5,000 mm; optional 5,300 mm |
| Track Width (Front / Rear) | Front: 1,876 mm (optional 1,896 / 1,920 / 1,950 mm); Rear: 1,820 mm (optional 1,860 mm) |
| Gross Vehicle Weight (GVW) | 18,000 kg |
| Curb Weight | 12,260 kg |
| Tire Size | 10.00R20 18PR steel radial tires; 6 units |
| Cab | Dongfeng Kinrun VR single-row cab; 3-person capacity; four-point floating suspension; electrically heated rear-view mirrors |




